With a litle help from my friends - går drillen lett :)

Jeg har hatt en liten tråd gående på Fiskersiden om mitt lille riggingsprosjekt av Evadaen, i tillegg til endel poster her på bloggen.

Jeg må si at responsen har vært formidabel, nyttig og ikke minst hjertevarmende. Før sentimentaliteten tar helt overhånd, så skal vi se litt på hva som skjedde i dag.

Metallspon

Sjelden har et så intetsigende bilde gledet meg så mye. :) Bildet over er av jernspon etter det siste hullet jeg har drillen opp i de rustfrie vinklene som skal bli takstativet på Evadaen. Via Fiskersiden fikk jeg tips om å bruke olje på både borr og det jeg borrer i, og å borre saaaakte. Resultatet ga de lange fine metallsponene på bildet, og jeg kom igjennom på kanskje 3 minutter. En betydelig forbedring fra de 40 minuttene jeg brukte på forrige hull, uten hjelpsomme råd og vink.

Fra de dypeste fjorder i Hardanger kom det en gladmelding fra Team Hardangertrolling (Ramon), som sa han hadde et aluminiumsrør i akkurat passe lengde jeg kunne få av ham. Dermed sparte jeg meg en dyr tur til SeaSea også. Takk for hjelpen Ramon!

Jeg fikk borret ferdig fire vinkler i ettermiddag før det siste borret mitt tok kvelden. Da har jeg bare en vinkel (hver skal ha to hull hver) og to T-jern igjen (som skal ha ett hull hver) så er alt det rustfrie ferdig drillet opp. Da gjenstår å kappe til røret fra Ramon, og å borre hull i alle aluminiumsrørene, så er det klart for endelig montering.

Kommentarer

Populære innlegg

The perfect settings for Lowrance? A guide on how to set up your 2D-sonar part I.

Perhaps the most repeated question in Facebookgroups and forums regarding marine electronics: "What are the best settings?" The bad news is that there is no uniform answer to that. The good news is that you can adjust settings according to conditions if you have a little knowledge as to what settings you should tweak and why. Here is part 1 of our guide to get the most out of your unit in regards to settings.

What is the difference between HDS Carbon and HDS Live?

Here we go again, a new generation of the Lowrance HDS. And with that Facebook and the different forums are flooded with questions referring to the difference between the new and the old. So what is the difference between Lowrance HDS Live and HDS Carbon?

Lowrance Elite Ti2 versus Elite FS

When Lowrance launches a new mid-range unit, it is a big deal. Forums and Facebookgroups light up with questions on the new stuff, differences towards the old stuff and questions on compatibility. As usual, we in Team Colibri will try our best to sort that out, both on a technical level and with a more practical in-your-boat approach.

Lowrance Hook 2 versus Lowrance Hook Reveal

You have to hand it to Lowrance when it comes to the name of their new entry-level line of sonar and chartplotters. We all want to hook up, and what better way to do that then by having our marine electronics reveal to us where the fish are?

What is the difference between Lowrance HDS Live and Elite Ti2?

Lowrance as a brand of marine electronis is well known to all anglers, but the differences within their range of different models seem to cause quite a few questions out there. Here we will try to outline the difference between Lowrance HDS Live (top end) and Lowrance Elite Ti2 (middle range). Lowrance Elite Ti2 vs Lowrance HDS Live (photo; lowrance.com) As usual, we will start with the tech and then try to translate those technical aspects to practical differences while out on the water. Hardware - housing, screen and connections. The screen and housing on Elite Ti2 is the same as on the previous Elite Ti, and again more or less the same as on HDS Gen 2 Touch. (The memorycard-door and mounting-bracket is different from HDS Gen 2 Touch.) This is by no means new stuff, and compared to the more advanced housing and screen on HDS Live, Elite Ti2 is starting to show its relative age. However, with that in mind it is worth noting that when looking at the competition, several of ...

Søk i denne bloggen